Miele M636EC Manual de Serviço

Installation instructionsfor freestanding, built-under andintegrated dishwashersIt is essential to read the operating andinstallation instructions bef

3.Building the dishwasherinto a nicheConnection to water and drainageshould be sited beside and not behindthe dishwasher for accessibility.Connections

Securing piecesTo ensure stability, the dishwasher mustbe fixed securely to the worktop (step 6).Two securing pieces are supplied forthis purpose.^ Fi

Now adjust the feet until the seal onthe top of the dishwasher is right upagainst the underside of theworktop, to which it will be screwedlater. Ensur

4.Matching the facia panel tothe height of adjacent drawerfrontsThe facia panel can be aligned with thedrawer fronts by adjusting the spacerbars.^ Usi

5.Fitting the (matching) doorfrontFixing brackets are already fitted onstainless steel door fronts. These frontscannot be shortened.(Go to "Fitti

^Hang the fixing bracket into the slitsin the machine door outer panel.^ Push the overhanging ends of thetemplates under the facia panel.^Adjust the f

^Drill the fixing holes to a depth ofabout 10 mm, using a 2.5 mm drillbit.^ Secure the fixing bracket to the doorfront using the countersunk screwssup

^Adjust the door front height on oneside and lightly screw in a T20 Torxscrew on this side.^Adjust the door front height on theother side and also lig

6.Securing the dishwasher^Open the dishwasher door.The holes in the securing piecesmust line up with the long holes inthe worktop cover plate. If this

7.Adjusting the door springsThe door springs are correctly adjustedwhen the door remains stationary whenleft open at 45 °.If the door drops down, then

These installation instructions apply to several different dishwasher models.Model numbers in this booklet refer to the model designation specifiedon

8.Matching the plinth facingof a kitchen runThe plinth area of the dishwasher isnormally covered with a plinth runmatching the kitchen furniture.The h

Built-under "U" modeldishwashers“U” model dishwashers are speciallydesigned for installing under acontinuous worktop.–The dishwasher is supp

Building in dimensions:Dishwasher models G 636 - G 698G 9751) Niche height 870 mm2) Niche height 820 mmAdjustment range approx. 5 cm (82 -87 cm total

1.Fitting protective cover plateto worktopThe underside of the worktop isprotected against steam rising from themachine by a special cover plate.,If t

2.Building the dishwasherinto its nicheConnection to water and drainageshould be sited beside and not behindthe dishwasher for accessibility.Connectio

Dishwasher height^Adjust the height of the dishwashermanuually before installing thedishwasher.Leave a space of approx. 5 mmbelow the worktop to allow

Screw feet^ Use a TORX T20 screwdriver toadjust the rear screw feet to therequired height.Higher = turn clockwiseLower = turn anti-clockwiseSeveral tu

3.Calculate the decor panelheightThe height of the dishwasher frontpanel can be adjusted to matchneighbouring kitchen units. To do thisyou will have t

Adapting the height of the decorpanel supplied^Mark the measurement X on the leftand right hand side of the decorpanel and on the decor frame strips.^

^Bow the panel slightly, pull it out fromunder the control panel and take itoff.^ Shorten the decor frame strips, andthe filler card (if used) by dime

Installing a freestanding dishwasher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Installing integrated "i" Dishwashe

^Refit the filler card (if used) and thedecor panel. Fit the decor panel intothe lower decor frame strip, positionthe filler card behind it, bow thede

5.Securing the dishwasherTo ensure stability, the dishwasher mustbe fixed securely to the worktop. Twosecuring pieces are supplied with thedishwasher

6.Adjusting the door springsThe door springs are correctly adjustedwhen the door remains stationary whenleft open at 45°.If the door drops down, the d

7.Adjusting the plinth returnThe plinth return on a "U" modeldishwasher can be adjusted between35 and 100 mm in 2.5 mm increments.^Push the

The plinth facing has two cutting lines.^Screw the plinth facing on to thebrackets with the cutting linestowards the top. Then pull the facingout even

8.Matching the plinth facing ofa kitchen runThe plinth facing supplied will fit withoutmodification:–for a maximum plinth return of 100mm–and when the

,Please follow the installationinstructions carefully.All electrical work should be carriedout only by a suitably qualified andcompetent person, in st

The wires in the mains lead arecoloured in accordance with thefollowing code:Green/yellow = earthBlue = neutralBrown = liveIf the colours of the wires

Connection to the water inlet,Water in the dishwasher mustnot be used as drinking water.–The dishwasher may be connectedto a cold or hot water supply,

Drainage–The machine drainage system isfitted with a non-return valve, whichprevents dirty water from flowingback into the machine via the drainhose.–

Freestanding dishwashersFreestanding dishwashers do notrequire any special installation fixings inthe kitchen, (except for plumbing andelectrical conn

"i"- Integrated dishwashersIf you would like to... you will need to order...convert an integrated ("i") dishwasherto a built un

Dishwasher model G 601 - G 632 G 801 - G 832Height Freestanding 84.7 cm(adjustable + 2.0 cm)-Height built-in models 81.7 cm(adjustable + 5.0 cm)83.7 c

Dishwasher model G 636 - G 645, G 975Height Freestanding 84.7 cm (adjustable + 4.0 cm)Height built-in models 81.7 cm (adjustable + 5.0 cm)Height of bu

Dishwasher model G 646 - G 657, G 692 G 846 - G 857, G 892Height Freestanding 84.7 cm(adjustable + 4.0 cm)-Height built-in models 81.7 cm(adjustable +

Dishwasher model G 681 - G 689G 693 - G 698G 881 - G 889G 893 - G 898Height Freestanding 84.7 cm(adjustable + 4.0 cm)-Height built-in models 81.7 cm(a

45

46

47

Alteration rights reserved (NovoPlusB,P,S) / 1206M.-Nr. 05 565 043 / 01en-GB

Integrated ("i") dishwashers"i" dishwashers are specially designedfor building under a continuousworktop.–The control panel with i

Building in dimensionsDishwasher models G 601 - G 632Dishwasher models G 636 - G 698,G 9751) Niche height 870 mm2) Niche height 820 mmAdjustment range

1.Fitting protective cover plateto worktopThe underside of the worktop isprotected against steam rising from themachine by a special cover plate.,If t

2. Fitting the facia panelThe dishwasher must not be used until the control panel has been correctlyfitted.Dishwashers with selector dial(G 601 - G 62

Dishwashers with programme selector buttons(G 632, G 692 - G 696, G 832, G 892 - G 896)^ Attach cap a to push button switch.^ Push the ventillation gr