Miele CS1112 Manual do Utilizador

Operating and InstallationInstructionsCeramic CombisetCS 1112CS 1122To prevent accidents andappliance damage,read these instructionsbeforeinstallation

One-ring burners use one heating strip,and two-ring burners and grill zonesuse two heating strips. Depending onthe model, the heating strips may besep

Turning a burner On/Off^To turn a burner on, press the controlknob down and turn it clockwise ato the desired setting.^To turn a burner off, turn the

Residual Heat IndicatorWhen a cooking zone is switched on,the On/Off indicator will light followedby the residual heat indicator.When the cooking zone

SettingsUse for Power level*Melt butter, chocolate, etc.Dissolving gelatinePrepare yogurt1-2Warming small quantities of food/liquidKeeping delicate di

Overheat protectionEach cooking zone is equipped with atemperature limiter. This featureautomatically turns off the heatingelement before the glass ce

Following these tips will allow you tomake the most of your ceramiccombiset.The cooking surfaceThe ceramic combiset is made of anextremely hard and du

Copper bottom and aluminum pansmay leave a residue on the combiset inthe form of metallic lines. This is normal.These lines can be removed using anon-

Do not use a steam cleaner to cleanthis appliance. Steam couldpenetrate electrical components andcause a short circuit. Pressurizedsteam could cause p

Ceramic surfaces^Wipe off any soiling using a dampcloth. Stubborn soiling is bestremoved with a shielded scraperblade.^Apply a ceramic cleaner (availa

,Repairs should only be carried out by an authorized technician inaccordance with local and national safety regulations. Unauthorized repairscould cau

IMPORTANT SAFETY INSTRUCTIONS...3Description of the combiset ...7CS 1112 ...

In the event of a fault which you cannoteasily fix yourself, please contact theMiele Technical Service Department atthe address on the back of this bo

MieleCare(USA only)MieleCare, our Extended ServiceContract program; gives you theassurance of knowing that yourappliance investment is covered by 5yea

22

Installation InstructionsIMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USEInformation is subject to change. Please refer to our website to

Note to the installer:Please leave this instruction bookwith the consumer for the localelectrical inspector’s use.The minimum distances given inthese

Safety distances above theapplianceThe minimum safety distance given bythe hood manufacturer must bemaintained between the combiset andthe hood above

Safety distances to the sidesof the applianceThe appliance should only be installedas shown in the illustrations, whilemaintaining the required safety

Safety distance from the wall coveringIf a wall covering is installed, a minimum safety distance must be maintainedbetween the countertop cut-out and

Installation dimensions CS 1112a Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e R

Installation dimensions CS 1122a Spring clipsb Appliance frontc Installation heightd Power supply box with connection cable,L=783/4" (2000 mm)e R

WARNING- When using your gasappliance follow basicprecautions, including thefollowing:This gas combiset conforms to alluniform safety codes andregulat

Cut out^Make the countertop cut-out for thedesired number of appliancesaccording to the dimensionsdrawings.Remember to maintain a minimumsafety distan

Installation of multipleappliancesWhen installing more than one combiset appliance, a support bar b must beinstalled between the appliances.Countertop

Sample calculations for a countertop cut-out for three appliancesAappliance widthminus 5/16"(8 mm)Bappliance widthCappliance widthminus 5/16"

a Spring clipsb Support barsc Space between support bar and countertopd CoverThe illustration represents the attachment of spring clips a and support

Attach the spring clips andsupport barsWood or solid surface countertops^Place the supplied spring clips aand the support bars b at themarked position

Granite countertopThe screws are not needed forgranite countertops.^Position and attach the spring clipsa and support bars b with strong,double-sided

Installing the appliance(s)^Feed the power cord down throughthe cut-out.^Place the front edge of the applianceinto the cut-out.^With a hand on each si

SealingThe appliance must not bepermanently sealed into the countertopwhen installed. The sealing strip underthe edge of the appliance provides asuffi

,CAUTION: Before installation orservicing, disconnect the powersupply by either removing the fuse,shutting off the main power ormanually "trippin

Disposal of packing materialsThe cardboard box and packingmaterials are biodegradable andrecyclable. Please recycle.Ensure that any plastic wrappings,

Technical safety~Installation, repair and maintenancework should be performed by a Mieleauthorized service technician. Work byunqualified persons coul

Alteration rights reserved / 3911INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOSTCURRENT PRODUCT SPECIFICATIONS, TECHN

~Be sure that the power cord doesnot come in contact with any "hot spots"after installation.Safety~DO NOT TOUCH THE COOKINGAREA OR THE VICIN

~Make certain that the power cords ofsmall appliances do not come incontact with the appliance. Theinsulation of the cable could becomedamaged. Danger

CS 1112a Variable burner :C 4" or 7" (100 mm or 180 mm) -Power: 700 W or 1800 Wb Standard burner :C 511/16" (145 mm) -Power: 1200 Wc Bu

CS 1122a Extended burnerC 7" or 7" x 107/16"(180 mm or 180 mm x 265 mm) -Power: 1500 W / 2400 Wb Standard burnerC 511/16" (145 mm)

Clean the combiset^Remove any protective coverings orstickers.^Before using for the first time, cleanthe appliance with a damp cloth anddry with a sof